My Humax Forum » Freeview SD » PVR 9150T, 9200T, 9300T

PVR9150T Continually Loading Version a4.39

(14 posts)
  1. User has not uploaded an avatar

    vinylrulesok

    new member
    Joined: Jul '12
    Posts: 2

    offline

    When I switch on my digital set top box it says “please wait” then it shows “Loader Version a4.39” and a yellow bar that shows it loading to 100% it then returns to “please wait” and continually tries to load the version a4.39.

    I have connected to my PC and updated manually but it still does the same.

    Can you help with this problem?

    | Sat 14 Jul 2012 10:56:15 #1 |
  2. Barry

    Barry

    senior admin
    Joined: Feb '11
    Posts: 11,040

    offline

    Welcome to the Forum

    a4.39 is the loader version, the software version should be something like 1.00.26.

    Check your PM's (top right of forum) I have access to a small app that might help.

    | Sat 14 Jul 2012 11:55:31 #2 |
  3. User has not uploaded an avatar

    vinylrulesok

    new member
    Joined: Jul '12
    Posts: 2

    offline

    Hi Barry,

    Thanks for the welcome.

    I have loaded PVR-9150T_1.00.26(a4_39).hdf via my PC but still no joy.

    | Sat 14 Jul 2012 12:08:55 #3 |
  4. Barry

    Barry

    senior admin
    Joined: Feb '11
    Posts: 11,040

    offline

    OK check your Private Messages (PM's)

    | Sat 14 Jul 2012 12:14:03 #4 |
  5. User has not uploaded an avatar

    Sandy

    new member
    Joined: Jul '12
    Posts: 2

    offline

    Hi - does anyone know how to plug in the default code 0000 if the handset isn't working (or doesn't appear to be)? I've tried to update manually using the buttons on the front of my 9150T but can't get any further when I have to put in the code since there aren't any numbers on the front of the recorder, only arrows,OK, etc.
    Thanks

    | Wed 25 Jul 2012 17:31:25 #5 |
  6. User has not uploaded an avatar

    markmhowells

    new member
    Joined: Oct '13
    Posts: 1

    offline

    Hi, I have a similar issue. Tried updating the software and still get Please Wait.... forever. I note that there may be a possible solution on this thread. Any help gratefully received.

    | Mon 14 Oct 2013 12:36:31 #6 |
  7. Barry

    Barry

    senior admin
    Joined: Feb '11
    Posts: 11,040

    offline

    You could try uploading a default file which I can provide.
    Send to the email address you registered with?

    | Mon 14 Oct 2013 13:24:06 #7 |
  8. User has not uploaded an avatar

    bobr

    junior member
    Joined: Nov '13
    Posts: 5

    offline

    Hi, I have a 9150T, just like vinylrulesok, it just keeps going round in circles, "loading" then "please wait", it had been fine until we had a power cut, now it will not start, have tried removing the aerial, switching on and pressing the menu button, nothing happened, also tried holding standby button and turning on, still nothing,
    any idea's please, keep it simple if poss please,

    Thank You

    | Fri 8 Nov 2013 20:07:49 #8 |
  9. User has not uploaded an avatar

    Martin Liddle

    special member
    Joined: Feb '11
    Posts: 4,685

    offline

    bobr - 5 hours ago  » 
    Hi, I have a 9150T, just like vinylrulesok, it just keeps going round in circles, "loading" then "please wait", it had been fine until we had a power cut, now it will not start, have tried removing the aerial, switching on and pressing the menu button, nothing happened, also tried holding standby button and turning on, still nothing,

    Assuming the Humax is out of warranty, try opening the case and remove the lead to the hard drive. If the box will now boot normally then the hard drive needs formatting in a PC.

    | Sat 9 Nov 2013 1:50:12 #9 |
  10. User has not uploaded an avatar

    bobr

    junior member
    Joined: Nov '13
    Posts: 5

    offline

    Martin, thanks for the reply, I will give it a go, I will let you know what happens

    Bobr

    | Sat 9 Nov 2013 19:59:44 #10 |

RSS feed for this topic

Reply »

You must log in to post.