My Humax Forum » Freeview HD » HDR 1800T, 2000T

Software Update Stuck on 50%

(90 posts)
  1. User has not uploaded an avatar

    DougF

    member
    Joined: Jan '15
    Posts: 29

    offline

    Have just tried an ota update using settings/installation/softwareupdate/automatic update and it found nothing. Am I doing something wrong?

    | Fri 27 Mar 2015 19:38:05 #41 |
  2. Barry

    Barry

    senior admin
    Joined: Feb '11
    Posts: 11,040

    offline

    What version of software does your unit have now?

    | Fri 27 Mar 2015 21:03:55 #42 |
  3. User has not uploaded an avatar

    DougF

    member
    Joined: Jan '15
    Posts: 29

    offline

    1.01.13

    | Fri 27 Mar 2015 21:13:18 #43 |
  4. Barry

    Barry

    senior admin
    Joined: Feb '11
    Posts: 11,040

    offline

    That is the latest.

    | Fri 27 Mar 2015 21:30:22 #44 |
  5. User has not uploaded an avatar

    DougF

    member
    Joined: Jan '15
    Posts: 29

    offline

    Doh! And there I was getting all excited about an update. What a fool!

    | Fri 27 Mar 2015 22:17:10 #45 |
  6. User has not uploaded an avatar

    StuartE

    new member
    Joined: Mar '15
    Posts: 1

    offline

    Thanks everyone, particularly Barry, for the essential information in getting this upgrade to install. The essential bit is, and I quote, "If you have already tried disconnecting power then unit will not boot to on, but boots to standby even though you were touching channel down, so touch standby button on front of unit and immediately touch and keep touching the channel down button until a picture appears"

    Pressing standby and then the "V" was the info which was missing from the Humax support email, after which the upgrade downloaded from the USB (already in place) very quickly. 36 hours without the PVR and so much wasted time. Humax, you must do this better. At least I'll know what to do next time!

    | Sat 28 Mar 2015 9:10:44 #46 |
  7. User has not uploaded an avatar

    Nobby

    new member
    Joined: Mar '15
    Posts: 1

    offline

    My Parents have no access to the internet so can only get updated "over the air" . Tried update overnight - still only on 46% this morning , struggled to around 50% then got an error message and machine has turned itself off with a pink light . Can not turn the box on or off by hand held device .. Any ideas ?

    | Sat 28 Mar 2015 9:21:47 #47 |
  8. Barry

    Barry

    senior admin
    Joined: Feb '11
    Posts: 11,040

    offline

    @StuartE - Thank you for the feedback, those instructions were essentially for users whose units are stuck in an update loop, but if it worked for you all the better. My version of usb updating instructions posted in our FAQ's.

    @Nobby - Welcome to our Forum

    Pink led? The only led colours I am aware of are
    blue/off
    red/ standby and or recording
    purple flashing updating, on update complete.

    Is the led flashing?

    | Sat 28 Mar 2015 9:45:40 #48 |
  9. Barry

    Barry

    senior admin
    Joined: Feb '11
    Posts: 11,040

    offline

    Glutton for punishment, I downgraded a unit to 1.00.07 and loader 1.02 last night to see what happened with overnight updating again.

    At 09:00 this morning the led was flashing purple, so it was still trying to update, probably 3rd attempt, left it alone. A few minutes later the led turned blue (standby) so guessed it had finally managed to update, on checking this is correct, now has 1.01.13 and loader 1.04. Will repeat the exercise tonight.

    | Sat 28 Mar 2015 9:52:56 #49 |
  10. User has not uploaded an avatar

    Faust

    special member
    Joined: Jun '13
    Posts: 1,598

    offline

    This appears to have caused grief for the many which is an update that will be of benefit to the few.

    | Sat 28 Mar 2015 11:49:49 #50 |

RSS feed for this topic

Reply »

You must log in to post.