FVP 5000T where is the 5.1?

My Humax Forum » Freeview HD » FVP 4000T, 5000T

FVP 5000T where is the 5.1?

(10 posts)

cyclopse

new member
Joined: Mar '18
Posts: 4
offline

New Humax user here.

I like the 5000T and have only one issue. I am on the 1.03.37 firmware.

I have Dolby 5.1 showing on my Arcam processor with optical SPDIF output (with appropriate HD material). However, there is no Dolby 5.1 over HDMI. Shame because I think the HDMI Audio is slightly better. Anyone else having this issue?

Regards

Cyclopse

| Sun 4 Mar 2018 19:14:43 #1 |
grahamlthompson

special member
Joined: Feb '11
Posts: 14,442
offline

Hi welcome to our Forum. The 5000T has seperate digital audio out options for S/Pdif and HDMI. You just need to change the setting for HDMI out.

| Sun 4 Mar 2018 19:18:42 #2 |
cyclopse

new member
Joined: Mar '18
Posts: 4
offline

I wish it was that straightforward.

SPDIF and HDMI are both independently set to Dolby Digital.

Thanks

Cyclopse

| Sun 4 Mar 2018 19:28:51 #3 |
grahamlthompson

special member
Joined: Feb '11
Posts: 14,442
offline

cyclopse - 2 hours ago »
I wish it was that straightforward.
SPDIF and HDMI are both independently set to Dolby Digital.
Thanks
Cyclopse

I will try and find some 5.1 recorded content on my 5000T in 5.1 and try and replicate. My Yamaha AV receiver has on TV display of the source discrete channels.

| Sun 4 Mar 2018 21:56:59 #4 |
grahamlthompson

special member
Joined: Feb '11
Posts: 14,442
offline
Blue Planet II is in 5.1 on my FVP-5000T connected by HDMI.
Attachments
1. BluePlanetAudio.jpg (114.7 KB, 5 downloads) 6 years old
| Mon 5 Mar 2018 10:54:59 #5 |
aciddad

special member
Joined: Jun '12
Posts: 103
offline

Cyclopse,

I had the same problem. It was caused by the HDMI cable. Changing it cleared the problem. I think it was down to the specification of the cables. I have several but I don't know what HDMI version any of them are so it was try one and see.

David.

| Mon 5 Mar 2018 15:11:34 #6 |
cyclopse

new member
Joined: Mar '18
Posts: 4
offline

I tried a different HDMI cable but the original was Wireworld Silver so high quality. My Arcam AV processor still cannot see Dolby 5.1 over HDMI. Anyone else have this issue?

Thanks

Cyclopse

| Tue 20 Mar 2018 21:32:50 #7 |
grahamlthompson

special member
Joined: Feb '11
Posts: 14,442
offline

cyclopse - 14 hours ago »
I tried a different HDMI cable but the original was Wireworld Silver so high quality. My Arcam AV processor still cannot see Dolby 5.1 over HDMI. Anyone else have this issue?
Thanks
Cyclopse

Are you sure the source content has 5.1. Most HD content is DD2.0.

| Wed 21 Mar 2018 12:01:07 #8 |
cyclopse

new member
Joined: Mar '18
Posts: 4
offline

Are you sure the source content has 5.1. Most HD content is DD2.0.

Yes because I also have the Humax outputting SPDIF digital audio on the SPDIF output. Switch to SPDIF 5.1 digital shows up. Switch to HDMI audio and it changes to DTS Neo 6 because it sees it as a stereo signal.

Thanks

Cyclopse

| Wed 21 Mar 2018 21:25:11 #9 |
SSThing

special member
Joined: Nov '15
Posts: 1,306
offline

cyclopse - 10 hours ago »
Are you sure the source content has 5.1. Most HD content is DD2.0.
Yes because I also have the Humax outputting SPDIF digital audio on the SPDIF output. Switch to SPDIF 5.1 digital shows up. Switch to HDMI audio and it changes to DTS Neo 6 because it sees it as a stereo signal.
Thanks
Cyclopse

Double check your hdmi playback settings on your amp.
My Onkyo TX-nr3030 (which isn't currently setup because I have moved) has options to select the output for all the different types of signal input. That is to say, I can choose 2 channels to be processed up to 5.1, 2 to TX etc etc. I cannot remember if there is an option to select for direct playback /no processing but I imagine there is.

| Thu 22 Mar 2018 8:31:38 #10 |