Two things you could try:
1. Leaving the unit on when timers are due, if you already do that then...
2. Try setting Weekday repeat timers.
Is 1.00.26 the software version on the 9300?
My Humax Forum » Freeview SD » PVR 9150T, 9200T, 9300T
Graded PVR-9300T problems
(25 posts)-
| Fri 11 Oct 2013 9:34:22 #11 |
-
Morning Barry my PVR is at home but I think the software is 20012 and it's 28 I think, have I grounds to complain to Humax it's not ideal leaving it switched on seems poor on a new machine, is it my machine or a Humax thing
| Mon 14 Oct 2013 9:41:10 #12 | -
Worked all week for me, both as individual timers, and set as a weekday repeat.
Trying the same this week with individual timers again, and series link this time.
Try the weekday repeat, ie set one timer for each programme and then edit them.
| Mon 14 Oct 2013 9:46:24 #13 | -
Cheers Barry sounds complicated, but I will give it a go, I may consider trying it this week again and if it fails, I will leave the timers in the schedule and then Humax can see they are there but no recordings, I was hoping for a pain free Humax experience this time, looks like I might be wrong
| Mon 14 Oct 2013 10:11:02 #14 | -
Setting weekday repeats:
Highlight the timer and press OK.
Scroll down to Repeat, once highlighted, right arrow until Weekday appears, scroll down, highlight save and press OK - job done.
| Mon 14 Oct 2013 10:48:26 #15 | -
Afternnon Barry tried the last three nights to record chan4 at 5pm and 5.30pm I tried as you asked
once did not record
daily recorded till 5.41pm and I had the error icon
weekday recorded till 5.41pm had the error icon
can I try the older 2011 software version 26
and if I do try it and it's no better where can I get the 2012 vesion from| Thu 17 Oct 2013 12:30:02 #16 | -
Strange only getting a part record, are you definitely sure it is tuned correctly, ie only receiving from one transmitter?
| Thu 17 Oct 2013 14:42:24 #17 | -
How would I check this? I'm in Darwen and get the repeater from winter hill we only get about 14 channels, I'm on the wrong side to get winter hill and behind darwen moors I have tried in the past to get winter hill by turnimng my aerial but nothing and last night both my old 9150T and my new graded both stopped recording come/dine one finshed at 5.43pm and one at 5.46pm it's the first ime my 9150T as done any thing wrong since the update
| Fri 18 Oct 2013 9:22:30 #18 | -
See this post for manual tuning instructions:
http://myhumax.org/forum/topic/week-old-9300t-and-epg-wont-fill-up-for-week#post-7097
| Fri 18 Oct 2013 9:50:40 #19 | -
bw78007 - 57 minutes ago »
How would I check this? I'm in Darwen and get the repeater from winter hill we only get about 14 channels, I'm on the wrong side to get winter hill and behind darwen moors I have tried in the past to get winter hill by turnimng my aerial but nothing and last night both my old 9150T and my new graded both stopped recording come/dine one finshed at 5.43pm and one at 5.46pm it's the first ime my 9150T as done any thing wrong since the updateIn general the radiation from relay transmitters is vertically polarised and that from main transmitters is horizontally polarised. This means it is not sufficient to simply point your aerial away from a relay to a main and expect to get a good signal, you also need to rotate the aerial on its longitudinal axis so the elements go from vertical (relay) to horizontal (main).
| Fri 18 Oct 2013 10:34:49 #20 |
Reply »
You must log in to post.
