Hi,
I've got a humax hdr-1000s but only one of the receivers appears to be working.
I've swapped the input cables around and only 1 receiver is still working.
Any ideas on a fix?
My Humax Forum » Freesat HD » HDR 1000, 1010, 1100S
One receiver no signal
(10 posts)-
| Tue 26 Jan 2021 20:53:10 #1 |
-
Markovitz - 35 mins ago »
Hi,
I've got a humax hdr-1000s but only one of the receivers appears to be working.
I've swapped the input cables around and only 1 receiver is still working.
Any ideas on a fix?I presume you mean tuners. The box is a receiver. Why do you think only one tuner is working.
When you swapped the inputs what do you get on the TV and what before the swap ?
Can you give an example of what you think should work and does not. ?
| Tue 26 Jan 2021 21:30:39 #2 | -
Sorry, tuners..
Tuner 1 has a good signal.
Tuner 2 has no signal.Both tuners should have a signal as they are both connected to the lnb.
| Tue 26 Jan 2021 21:59:05 #3 | -
"Tuner 1 has a good signal.
Tuner 2 has no signal."If you swap the cables what do get?
What does it say at the bottom of the signal page?
Check the fitting of the F connector, it needs to make a good electrical circuit with no part of the braid or foil touching the inner wire. The braid or foil must be in contact with the F Connector.
| Wed 27 Jan 2021 9:09:32 #4 | -
If I swap the cables T1 still has good signal, T2 nothing.
It says connected with 1 cable.
Checked input cables as they both work on T1.
| Wed 27 Jan 2021 10:44:23 #5 | -
Markovitz - 1 min ago »
If I swap the cables T1 still has good signal, T2 nothing.
It says connected with 1 cable.
Checked input cables as they both work on T1.Looking like you may need a new lnb, or tuner 2 has failed (very rare) unless you have had water in the cabling that has got into the box. .
Try this to check tuner 2 is working.
Enter 104 to go to Channel 4 and press the instant record button to start a recording.
Enter 949 to go to BBC2-HD and press the instant record button to start a second recording.
Check you have both recordings in the recordings list.
Exit recordings list.
Use channel up/down buttons to confirm you have 3rd viewing channels available,
| Wed 27 Jan 2021 10:53:37 #6 | -
I cannot record and watch something else at the same time.
| Wed 27 Jan 2021 11:01:51 #7 | -
I found an earlier post on the forum where it recommended a factory re-set.
I've just done that and now tuner 2 is working and has good signal.
Must be a software glitch.
| Wed 27 Jan 2021 11:17:52 #8 | -
LNB must be working fine.
| Wed 27 Jan 2021 11:20:22 #9 | -
Markovitz - 11 mins ago »
Try again..Image too large. Need to reduce longest side to about 1200 pixels.
https://www.groovypost.com/howto/use-windows-10-photos-app-to-resize-images/
looks like bad news. Any sign of moisture ingress on tuner 2 in ?
With only one tuner you are restricted to recording two from the same transponder.
eg BBC1-HD and BBC2-HD should be recordable.
example.
102 BBC Two HD 10847 V
106 BBC One HD 10847 V
600 CBBC HD 10847 V
971 BBC Two HD Wales 10847 V
972 BBC One HD 10847 V
949 BBC Two HD 10847 V
979 BBC Two Wales 10847 V
978 BBC One NI HD 10847 VChannels on each transponder
https://www.adrive.com/public/JAWF7Y/FoxsatStaticMK2_011.pdf
| Wed 27 Jan 2021 11:39:40 #10 |
Reply
You must log in to post.
