My Humax Forum » Freesat HD » HDR 1000, 1010, 1100S

Humax 1100s problems?

(15 posts)
  1. foxleybob

    foxleybob

    special member
    Joined: Oct '19
    Posts: 116

    offline

    Hi guys (again).

    Sorry But I'm posting here as I have only just found where to post a new thread Doh!!!
    I posted on a previous thread of mine as was in a mucking fuddle about where to post
    I can't believe I'm getting too old lol

    Anyway, here's a copy & past of it.......

    Hi again guys.
    I'm posting a new question here as I got told off for posting wrongly last time and could not understand/find where to post a new thread?
    So..... been using my 1100s ok for a while now, but just recently I found when starting up the TV I have to stop & start the 1100s again before my LG TV will pick it up.
    It didn't do this before. It just picked it up when I turned on the TV (once I had identified the correct HDMI of course)
    It still takes forever to get going, but that's another story.
    Regards
    Bob

    | Tue 16 Mar 2021 18:10:58 #1 |
  2. brian

    brian

    special member
    Joined: Mar '11
    Posts: 1,054

    offline

    You have posted this in the wrong forum section, perhaps admin can move it to the correct area.

    Admin edit: Thank you, moved.

    | Tue 16 Mar 2021 19:52:11 #2 |
  3. REPASSAC

    REPASSAC

    special member
    Joined: Mar '11
    Posts: 4,100

    offline

    Suggestions:
    1. Check that the HDMI cable is correctly seated at both ends.
    2. Try another HDMI port on the TV.

    | Wed 17 Mar 2021 8:00:24 #3 |
  4. foxleybob

    foxleybob

    special member
    Joined: Oct '19
    Posts: 116

    offline

    sorry to be a pain guys (this forum isn't the easiest to use is it).
    Anyway I cannot find a post where I had problems with my Humax 11ooS
    and John L kindly gave me a few options to get it working again (are you there John? :D)
    I tried the first two options, a soft reset and unplugging the power etc for over 5 mins.
    still no go
    the finel suggestion was to "Go into the menu for a factory reset etc.
    So my question is...........
    how do I get into the menu if I can't get it working, please?

    | Tue 15 Jun 2021 13:47:28 #4 |
  5. REPASSAC

    REPASSAC

    special member
    Joined: Mar '11
    Posts: 4,100

    offline

    Suggest you try bring the HDR-1100S out of standby AFTER the TV has fully started.

    | Tue 15 Jun 2021 14:05:27 #5 |
  6. foxleybob

    foxleybob

    special member
    Joined: Oct '19
    Posts: 116

    offline

    REPASSAC - 16 hours ago  » 
    Suggest you try bring the HDR-1100S out of standby AFTER the TV has fully started.

    could you elaborate that for dummy, please?

    | Wed 16 Jun 2021 6:09:17 #6 |
  7. REPASSAC

    REPASSAC

    special member
    Joined: Mar '11
    Posts: 4,100

    offline

    Duplicate

    | Wed 16 Jun 2021 7:13:39 #7 |
  8. REPASSAC

    REPASSAC

    special member
    Joined: Mar '11
    Posts: 4,100

    offline

    Turn on the TV, wait until it shows a programme, then turn on the HDR-1100S. Smartish TV's take longer to boot and may not be ready when the HDR-1100S signals it .

    You do normally keep your HDR-1100S in standby when not being used?

    | Wed 16 Jun 2021 7:15:36 #8 |
  9. foxleybob

    foxleybob

    special member
    Joined: Oct '19
    Posts: 116

    offline

    Thanks.
    Yes, I do keep it on Standby, but that was another issue...
    I'd turn my LG Oled on selecting the HDMI for the Humax. Then had to turn it off & on through the remote to get "Freesat " to show and play the programs.
    I don't know if there is something wrong with the box?
    It's been a right old pain.

    Hope this makes sense?

    | Wed 16 Jun 2021 9:12:10 #9 |
  10. REPASSAC

    REPASSAC

    special member
    Joined: Mar '11
    Posts: 4,100

    offline

    Try turning the TV on and without selecting the Humax HDMI port, when the TV is fully on start the Humax.

    | Wed 16 Jun 2021 10:48:22 #10 |

RSS feed for this topic

Reply »

You must log in to post.